12-inch Sprinkler Head Replacement

Einleitung

When a hedge or plant has grown taller than the sprinkler head’s spout can spray, grass beyond the plant dies from lack of water. This fast fix will show you how to install the following sprinkler head: 1800 Series 12-inch Pop-Up PRS Sprinkler, 0-360° Pattern, Adjustable 8-15 ft. This will eliminate water waste and will spray water to areas you intend for the water to reach.

Was du brauchst

Schritt 1 12-inch Sprinkler Head

12-inch Sprinkler Head Replacement, 12-inch Sprinkler Head: Schritt 1, Bild 1 von 3

12-inch Sprinkler Head Replacement, 12-inch Sprinkler Head: Schritt 1, Bild 2 von 3

12-inch Sprinkler Head Replacement, 12-inch Sprinkler Head: Schritt 1, Bild 3 von 3

Dig and remove dirt around the existing sprinkler head and several inches around connected PVC.
Place the dirt in 5 gallon the buckets or on the surface near the hole.
Dig until the hole is at least 14 inches below the PVC pipe allowing room for the flex riser.

Bearbeiten

Schritt 2

12-inch Sprinkler Head Replacement: Schritt 2, Bild 3 von 3

Rinse all around the sprinkler head and PVC with water.
This will allow for a clean installation of the new sprinkler parts and keep the dirt from entering the new parts.

Bearbeiten

Schritt 3

12-inch Sprinkler Head Replacement: Schritt 3, Bild 3 von 3

Remove the old sprinkler head and riser.
Turn counterclockwise until the old sprinkler head and or riser is removed.
Rinse area for clean installation.

Bearbeiten

Schritt 4

12-inch Sprinkler Head Replacement: Schritt 4, Bild 3 von 3

For this step, wrap 4 threaded ends with Teflon tape: both ends of the flex riser and one end of each swing joint elbows.
Wrap Teflon tape clockwise around the threaded part of each of the above-mentioned sprinkler connections.
Put three complete layers of tape on each of the threaded ends. This will allow for a tighter and secure fit.

Bearbeiten

Schritt 5

12-inch Sprinkler Head Replacement: Schritt 5, Bild 3 von 3

Screw clockwise, the new Teflon wrapped the threaded part of an elbow, into the pipe in the ground.
This is the location of the old sprinkler head and riser.
Confirm that the part is installed snugly and not cross-threaded.
Caution: Do not over tighten.

Bearbeiten

Schritt 6

Screw the threaded end of the elbow onto the 12" sprinkler head.
Confirm that the part is installed snugly and not cross-threaded.
Caution: Do not over tighten.

Bearbeiten

Schritt 7

12-inch Sprinkler Head Replacement: Schritt 7, Bild 3 von 3

Confirm that Teflon tape has been applied to both threaded ends.
Screw one end of the blue flex tubing onto the elbow in the previous step.
Screw the other end of the flex tubing onto the last remaining elbow.
Caution: Confirm that the part is installed snugly and not cross-threaded. Do not over tighten.

Bearbeiten

Schritt 8

12-inch Sprinkler Head Replacement: Schritt 8, Bild 3 von 3

Lower the 12-inch sprinkler head and flex tubing down into the hole.
Adjust the new sprinkler head so it is level with the sidewalk or surface.
Adjust flex tubing as necessary so that there are no kinks and that the joints are still tight.

Bearbeiten

Schritt 9

Test the new parts to confirm that there are no leaks.
Guard your eyes and other things that you don't want to get wet.

Bearbeiten

Schritt 10

12-inch Sprinkler Head Replacement: Schritt 10, Bild 3 von 3

Hold the sprinkler head in place, vertically, while carefully putting the dirt into the ground by hand. Using your hands allows for a gentle pressure on the sprinkler head versus using a tool that could crack or break it.
Add dirt in layers, compressing the dirt by hand, around the sprinkler head.
Do not compress the dirt too much, as the tubing can be crushed.

Bearbeiten

Schritt 11

Turn on the sprinkler system.
At this point full water flow should come out of the new sprinkler head.
If the flow is good, adjust the nozzle direction and radius by turning the nozzle head and shaft.
Check water pressure and nozzle lift after landscaping has returned around sprinkler head.